Manufacturing

How Is Metallic Yarn Made? Film to Wound Yarn

Metallic yarn is made by metallising a base film, slitting it into thin strips, twisting or covering it onto a core where needed, and winding it onto packages. This guide covers each stage and its checks.

By Suvarnatantu Technical Team Published 8 min read
Illustrated cover: a gold film sheet slit into threads that twist into a ply and wind onto a round package, for the article How Is Metallic Yarn Made? Film to Wound Yarn.
Zari Yarnmetallic yarnTPMmanufacturing processquality checksslittingtwisting

Metallic yarn is made by metallising a base film, slitting the film into fine strips, twisting those strips, alone or around a core, and winding the finished yarn onto packages. Each stage fixes a different property: shine, width, strength, handle and package quality.

This guide from the Suvarnatantu technical team explains the metallic yarn manufacturing process in plain order, with the quality checks that matter at each step. It is a general account of how film-based metallic yarn is made. Routes differ between mills, so confirm details of any yarn against a written specification.

What are the main stages in how metallic yarn is made?

Film-based metallic yarn follows a fairly standard sequence. A base film is prepared and given a metallic layer. The layer is protected and coloured. The wide film is then slit into narrow strips, which are twisted or combined with a core, and finally wound into packages for despatch.

Seen from the buyer's side, the stages group into four decisions: what the film is and how it is metallised, how finely it is slit, how it is twisted or covered, and how it is packed. A fault introduced early usually cannot be corrected later, which is why consistency is mostly a matter of controlling the first stages.

  • Base film preparation and metallising
  • Coating and colouring of the metallised film
  • Slitting into strips of the required width
  • Twisting, or covering a core, to the stated construction
  • Winding, inspection and packing

How is the film metallised and coloured?

The starting point is a base film, commonly a polyester type. A thin metallic layer is applied to its surface, which gives the bright, reflective look associated with gold, silver and other metallic shades. The layer is very thin, so its adhesion to the film matters as much as its brightness.

Colour comes from coatings or lacquers applied over the metallic layer, and the same coating also protects the surface during later handling. Coating thickness, curing and uniformity across the width of the film all affect how evenly a shade reads in the final yarn.

Quality checks at this stage are mostly visual and comparative. The film is examined for pinholes, streaks, scratches and patchy coating, and shade is compared with an approved reference under consistent light. Our post on colour matching across batches explains why this comparison matters so much to weavers.

How is metallised film slit into yarn?

The wide metallised film is cut lengthwise into narrow strips on a slitting machine. The strip width largely determines the denier of the finished yarn, so slitting is where the fineness of the yarn is set. Even a small variation in width shows up as a variation in denier along the length.

Clean slit edges are important. Rough, burred or wavy edges can cause the strip to catch on guides during twisting, to break in weaving, or to look uneven in the cloth. Blade condition, tension control and a steady running speed all influence edge quality.

Checks here include measuring strip width at intervals, inspecting edges, and confirming that the slit strips wind onto their bobbins at even tension. A strip wound too tightly or loosely can behave differently when it is unwound for twisting.

  • Strip width sets the denier of the yarn
  • Edge quality affects breaks and appearance
  • Even winding tension helps later twisting

How are zari yarn production steps different from plain metallic yarn?

The zari yarn production steps share the same early stages but then diverge in construction. A flat metallic strip can be used as it is, or it can be twisted. For zari-type yarns, the metallic strip is typically wrapped or covered around a core yarn, which gives the thread more body, strength and a rounder, more traditional look.

The choice of core, such as a textile filament, and how closely the strip is laid around it, changes the handle, the weight and how the yarn performs on a loom or an embroidery machine. Our guide to what zari yarn is describes these constructions and where each is used.

Because the construction determines behaviour, the same shade can feel and weave very differently across a flat strip, a twisted yarn and a covered yarn. This is why the specification should name the construction and not only the colour.

How is metallic yarn twisted and wound?

Twisting turns the slit strip, or the strip with its core, into a stable yarn. The key parameters are TPM (turns per metre) and twist direction, usually described as S or Z. TPM influences how compact, firm and lustrous the yarn looks, and how well it resists splitting or opening up in use.

Twist must be controlled carefully. Too little can leave the yarn loose and prone to snagging, while too much can make it stiff or reduce its shine. Twist direction matters when the yarn is combined with other yarns or used in a specific machine setup, so it should be written down and not assumed.

After twisting, the yarn is wound onto cones, tubes or other packages. Good winding means even tension, clean package edges and no cobwebbing or loose layers, so that the yarn unwinds smoothly at the loom or machine. Our post on what to state in an enquiry covers how to describe denier, TPM, twist and package form.

What metallic yarn quality checks should buyers look for?

Metallic yarn quality checks run through the whole route, not only at the end. In general terms, buyers can expect a mill to look at denier, twist, strength and elongation, shade and lustre, and package appearance. The exact tests and limits depend on the yarn and the agreed specification, so ask for them in writing.

A practical way to use this knowledge is to link each check to a risk you care about in your own process. Breaks on the loom point to strength and edge quality, uneven cloth points to denier and twist variation, and shade differences between lots point to coating and batch control.

Use the following list as a starting point when you review a sample or a supplier.

  • Denier: is it within the range agreed in the specification?
  • TPM and twist direction: do they match what was stated?
  • Strength and elongation: does the yarn run without frequent breaks?
  • Shade and lustre: does it match the approved reference under the same light?
  • Package: is winding even, with clean edges and no loose layers?
  • Documentation: are the specification and any test details recorded for repeat orders?

How should you use this when sourcing metallic yarn?

Knowing how the yarn is made helps you ask better questions. Instead of asking only for gold at a certain denier, state the type, construction, TPM, twist direction, colour reference, package form and end use. Then approve a sample on your own loom or machine before committing to bulk.

Keep the approved sample and its specification on record so that repeat orders can be compared against it. You can also read about our manufacturing, browse our metallic yarn and zari yarn ranges, or see the typical references on the specifications page. Typical references are not a guarantee, so confirm each parameter for your order.

Read next

Frequently asked questions

What is metallic yarn made from?

Film-based metallic yarn starts with a base film, commonly polyester, that carries a thin metallic layer and a protective coloured coating. The film is slit into strips and then twisted, or covered around a core in zari-type yarns. The exact materials depend on the type, so confirm them in the specification.

What decides the denier of metallic yarn?

Mainly the width of the slit strip, along with the film thickness and any core used. Slitting sets fineness, so even width variation shows as denier variation along the length. State the denier you need and ask how it is checked on the yarn supplied.

Why does TPM matter in metallic yarn?

TPM, or turns per metre, affects how firm, compact and lustrous the yarn is, and how well it resists opening up or splitting during use. Too little or too much twist can cause handling problems. Write the TPM and the twist direction, S or Z, into your enquiry.

How is zari yarn production different from plain metallic yarn?

The early stages are similar, but zari-type yarn usually has the metallic strip wrapped or covered around a core, which adds body and strength. Plain metallic yarn may be a flat strip or a simple twist. Construction changes handle and performance, so name it in your specification.

What quality checks should I ask a metallic yarn supplier about?

Ask about denier, twist, strength and elongation, shade and lustre against an approved reference, and package appearance. Request that the specification and test details be recorded so repeat lots can be compared. Always approve a sample on your own loom or machine before bulk.