Technical Knowledge

Metallic Yarn TPM and Twist Direction: S and Z Twist

TPM is the number of twists per metre in a yarn, and S or Z is the direction of that twist. This guide shows weavers, mills and embroidery units how to state and check both for metallic yarn and zari.

By Suvarnatantu Technical Team Published 7 min read
Illustrated cover: two mirrored sets of twisting gold strands, one slanting each way, over a woven grid for the article on metallic yarn TPM and S and Z twist direction.
Zari Yarnmetallic yarnspecificationTPMtwist directionS twistZ twist

Metallic yarn TPM twist direction describes how tightly a yarn is twisted and which way. TPM is turns per metre. S and Z name the slant of those turns, like the middle stroke of each letter. Both belong in every specification, because they change how the yarn runs, lies and looks.

This guide, from the Suvarnatantu technical team, explains what each term means, where twist matters in warp, weft, jacquard and machine embroidery, and how to word it in an enquiry. Figures here are general reference points, not a specification for any particular yarn.

What does TPM mean in metallic yarn?

TPM stands for twists per metre, the number of complete turns the yarn makes along one metre of its length. In a twisted metallic yarn or zari yarn, the metallic element is usually twisted with or around a base filament, and TPM records how much twist was put in.

TPM is a count of turns, not a measure of strength or quality on its own. A higher TPM gives a tighter, rounder, firmer yarn. A lower TPM gives a softer, flatter yarn that spreads light more evenly but is less compact.

Many flat metallic yarns carry little or no twist, so TPM may not apply to every product. Always ask whether the yarn you need is twisted at all, and if so, at what TPM.

What are S twist and Z twist in zari yarn?

Twist direction is the slant of the spirals when you hold the yarn upright. If the spirals slope like the centre of the letter S, from upper left to lower right, it is S twist. If they slope like the centre of the letter Z, from lower left to upper right, it is Z twist.

The direction is a property of the yarn, not of which end you look at. Turn the yarn around and the slant still reads the same. This makes it easy to check on a cone with a simple visual look.

In S twist Z twist metallic yarn, neither direction is better in itself. What matters is how the direction works with the other yarns it is woven or stitched with, and with the machine that handles it.

Why do TPM and twist direction matter in weaving?

On a loom, twist affects how the yarn behaves under tension and how it sits in the cloth. A yarn with too little twist can open up, split or snag at the heald, reed or shuttle. A yarn with too much twist can curl, kink or snarl when tension drops.

Twist also affects appearance. The direction and tightness change how light falls on the surface, so two yarns of the same denier and colour can look different in the fabric. When a warp and weft are twisted in opposite directions, the surface texture and the way the yarns settle against each other can differ from when they match.

Points weavers commonly review:

  • Warp use: a firmer twist usually helps the yarn resist abrasion and fuzzing, but it must still run without kinking.
  • Weft use: the yarn must unwind freely from the pirn or shuttle without snarling or untwisting.
  • Jacquard and brocade work: floats and pattern areas show twist effects clearly, so consistency across cones matters.
  • Mixed yarns: check how the metallic yarn twist direction relates to the twist of the ground yarn.

How does twist affect machine embroidery?

In embroidery, the yarn passes through needles, tension discs and guides at speed, and twist is one factor in whether it runs cleanly. Twist that opens up can cause fraying or breaks at the needle eye. Twist that is too tight can make the thread spring back and loop on the fabric surface.

Direction matters because the needle and rotating parts add their own twisting action. Some units find that one direction holds its twist while the other loosens during stitching. This depends on the machine and set-up, so it is best confirmed by a trial rather than assumed.

For embroidery, test the yarn on the actual machine, with the actual needle size and speed, before approving a production quantity. A short run on the real design shows breaks, shine and loop behaviour better than any figure on paper.

How do you specify twist for zari yarn?

To specify twist for zari yarn, write the TPM, the direction (S or Z), and the end use together. Add the yarn type, denier, colour and package form around it. A line such as the one below leaves little room for a wrong guess.

State twist in a form a mill can act on:

  • Twist: yes or no (flat, untwisted yarns should be marked as such).
  • TPM: a number or a range, with the tolerance you can accept agreed in writing.
  • Direction: S or Z, matched to your ground yarn and machine.
  • End use: warp, weft, jacquard, border, or machine embroidery.
  • Reference: a sample or retained cone, so both sides compare against the same yarn.

How do you check TPM and twist direction on incoming cones?

Direction is checked by eye. Hold a short length upright and read the slant of the spirals against the letters S and Z. Do this on cones from every lot, since a mix-up in direction is easy to miss and costly when found on the loom.

TPM is usually checked with a twist tester, which untwists a set length of yarn and counts the turns. Take several samples from different cones and compare them with the agreed figure. If you have no tester, ask the supplier for the test method and results, and compare cones by running them on a trial.

Record the readings against the lot number. If a problem appears later, such as uneven shine or breaks, you can then trace it back to the cone and compare it with the approved sample. Handling and storage also matter, since yarn that is dropped, crushed or left loose can lose its shape.

What should you confirm with the supplier before ordering?

Agree twist in writing, not by phone. Confirm whether the yarn is twisted, the TPM, the direction, and how consistent it will be across lots. Ask for a sample made to that specification, and approve it on your own loom or machine.

If your requirement is not fixed, say so and describe the problem you want to solve, for example breaks at the needle or kinks in the weft. The mill can then suggest what to try. Keep the approved sample, because it becomes the reference for every later order.

Read next

Frequently asked questions

What is a typical TPM for metallic yarn?

There is no single typical TPM. It depends on the yarn construction, denier and end use, and many flat metallic yarns are untwisted. Ask the mill for the TPM of the specific yarn, agree it in writing with a tolerance, and confirm it on a trial before bulk orders.

Is S twist or Z twist better for zari yarn?

Neither is better in itself. The right direction depends on the ground yarn, the loom or embroidery machine and the look you want. Test both on your own set-up if unsure, then fix the direction in the specification so every lot arrives the same.

How can I tell S twist from Z twist by eye?

Hold a short length of yarn upright and look at the slant of the spirals. If they follow the centre stroke of the letter S, it is S twist. If they follow the centre stroke of the letter Z, it is Z twist. The reading is the same from either end.

Can twist affect breaks in machine embroidery?

Yes, twist is one factor. Yarn that opens up may fray at the needle, and yarn that is too tight may loop. Needle size, tension and speed also play a part, so run a trial on your machine with the actual design before approving production.