Metallic Yarn

Metallic Yarn Types: M, MX, ST and MH Explained

M, MX, ST and MH are trade designations for metallic yarn. This guide explains how to read them, what separates the constructions, and how to shortlist a type for weaving or embroidery.

By Suvarnatantu Technical Team Published 7 min read
Illustrated cover: four distinct gold threads, plain, glossy, twisted and fine, across a dark woven panel for the article Metallic Yarn Types: M, MX, ST and MH Explained.
metallic yarn typesM typeMX typeST typeMH typeweavingembroidery

Metallic yarn types such as M, MX, ST and MH are trade designations for different constructions of film-based metallic yarn. They separate by how the metallic layer is built, protected and finished, which decides handle, durability and suitability for weaving or embroidery. Always confirm each letter code against a written specification.

These letter codes are not a single universal standard, and mills may use them with slightly different meanings. This guide therefore explains what to compare behind each code, how the types are commonly shortlisted, and which questions to settle before wedding-season production planning begins.

What do M, MX, ST and MH mean in metallic yarn?

M, MX, ST and MH are short type codes used in the metallic yarn trade to name a construction family. They are shorthand, much like grade codes in other textile materials. The letters tell you which family a yarn belongs to, but not its denier, width, twist, colour or finish.

Because the codes are used by trade convention and not by one governing standard, the same letters can carry small differences from one supplier to another. A buyer who orders only by letter code risks receiving a yarn that behaves differently from the one approved earlier.

The safe practice is to treat the code as a starting point. Ask for the construction, the base film or core, the coating, the denier and the intended use in writing, then match all of it against your own approved reference.

What is M type metallic yarn?

M type is generally the reference point in the group, the basic metallic yarn construction from which the other types are described. It is the family most buyers meet first when they look at metallic yarn for weaving and embroidery.

For a weaver, M type is usually the starting question: does the basic construction already meet the fabric requirement? If the cloth is not washed hard, not pressed hot and not worn against the skin for long periods, a basic construction may be adequate and keeps the specification simple.

Check these points before settling on M type:

  • Brightness and colour match against your approved shade card
  • Handle and flexibility on your loom or embroidery machine
  • Behaviour during washing, pressing or finishing of your fabric
  • Consistency of width and denier from lot to lot

How does MX type metallic yarn differ?

MX type is commonly discussed as the more protected or reinforced step beyond the basic construction. In practice, buyers look to MX when the metallic layer needs better protection against rubbing, flexing or processing, or when the yarn will pass through more demanding handling.

The reason to ask about MX is mostly durability in use. Fabrics that are woven tightly, brushed, or stitched at speed place more stress on the metallic surface. A construction that protects that surface may hold its appearance better through the process.

The trade-off is usually in handle and in how the yarn feels on the machine. A more protected construction can behave differently in tension and bending. Confirm with a trial run, not with a description alone, and compare it against your current M type result.

Where do ST and MH type metallic yarn fit?

ST and MH type codes are used for further construction variants, and this is where supplier-to-supplier differences matter most. Their meaning is less uniform than that of M, so a written definition from the mill is essential before you plan a lot around either one.

Buyers typically consider these variants when the standard family does not meet a particular requirement, such as a specific handle, a stronger resistance to processing, or a distinct surface effect on the finished cloth. Ask directly what problem the variant is built to solve and what it gives up in return.

When you request ST type metallic yarn or MH type metallic yarn, ask the supplier to state:

  • How the construction differs from the basic M type
  • The intended end use and the processes it is designed to survive
  • The denier, width and finish options available
  • Any handling or storage guidance for the yarn

How do you choose a metallic yarn type for weaving and embroidery?

Start from the fabric, not from the code. Write down the end product, the weave or stitch density, the machine, and the finishing and care it will go through. Those four things narrow the choice faster than any catalogue.

Weaving and embroidery stress the yarn differently. In weaving, the yarn is carried under tension through reed and heddles, often as weft or as a supplementary pattern thread. In embroidery, it is pulled repeatedly through needle eyes at speed, so flexibility and surface protection matter more.

A practical shortlisting sequence runs as follows:

  • Define the application and the finishing the cloth will undergo
  • Shortlist two or three type codes and get written specifications for each
  • Request samples of each in the same shade and denier
  • Run a small trial on the actual loom or embroidery machine
  • Wash, press or finish the trial piece the way production will
  • Record the result and fix the approved type in the purchase specification

What should be in the specification before you place an order?

A type letter alone is not a specification. Build the order document around the properties that determine behaviour: type code, denier, width or form, colour reference, finish, packing form and the intended application. Technical data on the specifications page gives a sound reference for the fields worth fixing.

Colour deserves its own line. Metallic shades read differently on the cone, in the cloth and under different light, so approve colour on a woven or embroidered sample, not on the bobbin. The colours page shows the range of shades to refer to when you set the reference.

Finally, keep an approved sample on file. Lot-to-lot checks are far easier when both sides hold the same physical reference, and disputes over type or finish are settled faster. For export lots, the same record helps the importer match what arrives with what was approved.

How do you plan sampling before a busy production season?

Wedding and festival seasons compress timelines, which makes late discovery of a mismatch expensive. Do the type comparison early, while there is still room to change a specification without disturbing the loom plan.

Order samples of each shortlisted type, test them on the same machine setting, and keep notes on breakages, shedding, tension changes and surface appearance. Compare the notes, not impressions. The samples page explains how to request material for this kind of trial.

If your range spans both weaving and embroidery, test each separately. A type that suits a woven border may not be the best choice for dense machine embroidery, and the reverse is equally possible. Treat them as two specifications.

Read next

Frequently asked questions

Are M, MX, ST and MH defined by a universal standard?

No. They are trade designations, and the exact meaning can vary between suppliers. Treat the letter as a family name, then ask for a written specification covering construction, denier, width, finish and intended use. Approve a physical sample so both sides share the same reference.

Which metallic yarn type is best for embroidery?

There is no single best type. Embroidery pulls the yarn through a needle repeatedly, so flexibility, surface protection and consistent denier matter. Shortlist two or three types, sample them on your machine at production speed, and choose from the trial results.

Can the same type be used for weaving and embroidery?

Sometimes, but test each use separately. Weaving stresses the yarn through tension, reed and heddles, while embroidery stresses it through needle passage and speed. A type that performs well in one may behave differently in the other.

What should I ask a supplier besides the type code?

Ask for the construction, denier, width or form, colour reference, finish, packing form and recommended applications. Also ask how the type differs from the basic M type and what handling guidance applies. Request samples so you can verify the answers on your own equipment.